Evolution of core–rim structures and phase transformations in infra-red transmitting Y-α-SiAlON ceramics

Core–rim structures were observed as common features in Y-α-SiAlON ceramics hot-pressed between 1550?1950 °C. We found most dopants were taken into α’-rims, and a transition layer grown first on α-cores from liquid-phase over-saturated with metal solutes. Elongated β’-grain were formed as minor phase with α’- or AlN-cores thus only after the α’ matrix had consumed up all Y solutes, revealing that the α’ → β’ transformation is controlled by the transient liquid-phase and similar defects and dangling bonds could be detected in both SiAlON phases by cathodoluminescence. Quantitative assessment of Y_m/3Si_12?(m+n)Al_m+nO_nN_16?n demonstrates the multiphase evolution, initiated by over-saturation of Y solutes at low temperatures thus retaining α-phase as cores to lower the infra-red transmittance, dictated by homogenization of Al solutes at higher temperature. The elimination of those phase boundaries leads to better dopant and sintering design for achieving transparent and high-performance SiAlON ceramics.     

Raman and X-ray photoelectron spectroscopy study on the influence of La2O3 on the melt structure of SiO2–CaO–Al2O3–MgO

In order to gain more insights into the influence of rare earth elements on the melt structure of SiO₂–CaO–Al₂O₃–MgO glass ceramics, Raman and X-ray photoelectron spectroscopy techniques were used to study the influence of La₂O₃ on the Si–O/Al–O tetrahedron structure within SiO₂–CaO–Al₂O₃–MgO–quenched glass samples in this study. Results showed that some Raman peak shapes at low frequencies (200–840 cm^?1) changed significantly after the addition of La₂O₃, compared to the high frequency (840–1200 cm^?1) region that corresponds to the [SiO₄] structure, suggesting that the depolymerization of the low-frequency T–O–T (T=Si or Al) structure was more prevalent with La³⁺ addition. Besides, the depolymerization extent of the Si–O/Al–O tetrahedral network varied when the melt composition altered. Most notably, depolymerization is the most significant at a low CaO/SiO₂ ratio (0.25) and a high Al₂O₃ content (8%). Meanwhile, La³⁺ can promote the transformation of Si–O–Si and Al–O–Al bonds to the Si–O–Al ones, thereby forming a complex ionic cluster network interwoven with Si–O and Al–O tetrahedrons.     

In situ synthesis of Al2O3–SiC powders via molten-salt-assisted aluminum/carbothermal reduction method

Al₂O₃–SiC composite powder (ASCP) was successfully synthesized using a novel molten-salt-assisted aluminum/carbothermal reduction (MS-ACTR) method with silica fume, aluminum powder, and carbon black as raw materials; NaCl–KCl was used as the molten salt medium. The effects of the synthesis temperature and salt-reactant ratio on the phase composition and microstructure were investigated. The results showed that the Al₂O₃–SiC content increased with an increase in molten salt temperature, and the salt–reactant ratio in the range of 1.5:1–2.5:1 had an impact on the fabrication of ASCP. The optimum condition for synthesizing ASCP from NaCl–KCl molten salt consisted of maintaining the temperature at 1573 K for 4 h. The chemical reaction thermodynamics and growth mechanism indicate that the molten salt plays an important role in the formation of SiC whiskers by following the vapor-solid growth mode in the MS-ACTR treatment. This study demonstrates that the addition of molten salt as a reaction medium is a promising approach for synthesizing high-melting-point composite powders at low temperatures.     

Application of Cr3C2/C composite powders synthesized via molten-salt method in low-carbon MgO–C refractories

High-performance and low-carbon MgO–C refractories are important refractories for smelting ultra-low carbon steel and clean steel. Based on this, Cr₃C₂/C composite powders were synthesized by the molten-salt method, and used as an additive to prepare low-carbon MgO–C refractories under nitrogen atmosphere. The phase, morphology and oxidation kinetics of Cr₃C₂/C composite powders were studied. In addition, the effect of Cr₃C₂/C composite powders on the morphology, mechanical properties, thermal shock resistance, and corrosion resistance of MgO–C refractories was investigated. The results indicated that the Cr₃C₂/C composite powders exhibited superior oxidation resistance than flake graphite. Moreover, the Cr₃C₂/C composite powders were introduced into the MgO–C refractories. Compared with the sample without Cr₃C₂/C composite powders, the introduction of 1 wt% Cr₃C₂/C composite powders significantly improved the thermomechanical properties and corrosion resistance of the material, its CMOR, CCS before and CCS after thermal shock were 9.06 MPa, 50.40 MPa and 32.60 MPa, respectively, and the corrosion index was significantly reduced from 44.6% to 26.5%.     

Dual functions of three-dimensional hierarchical architecture on improving the rate capability and cycle performance of LiNi0.8Co0.1Mn0.1O2 cathode material for lithium-ion battery

The main obstacles in lithium-ion battery are limited by rate performance and the rapid capacity fading of LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811). Herein, a novel three-dimensional (3D) hierarchical coating material has been fabricated by in situ growing carbon nanotubes (CNTs) on the surfaces of Ni–Al double oxide (Ni–Al-LDO) sheets (named as LDO&CNT) with Ni–Al double hydroxide (Ni–Al-LDH) as both the substrate and catalyst precursor. The resultant LDO&CNT nanocomposites are uniformly coated on the surfaces of NCM811 by the physical mixing method. The rate capability of the resultant cathode material retains to 78.80% at a current rate of 3C. Its capacity retention increases by 6.7–14.42% compared with pristine NCM811 after 100 cycles within a potential range of 2.75–4.3 V at 0.5C. The improved rate capability and cycle performance of NCM811 are assigned to the synergistic effects between Ni–Al-LDO and CNTs. The hierarchical LDO&CNT nanocomposites coating on the surface of NCM811 avoids the aggregation of conductive CNTs and the stacking of Ni–Al-LDO nanosheets. Furthermore, it accelerates Li⁺ and electrons shuttle and reduces the reaction of Li₂O with H₂O and CO₂ in air, which results in Li₂CO₃ and LiOH alkali formation on the NCM811 surface.     

A Complexing Agent to Enable a Wide-Temperature Range Bromine-Based Flow Battery for Stationary Energy Storage

Bromine-based flow batteries (Br-FBs) are considered one of the most promising energy storage systems due to their features of high energy density and low cost. However, they generally suffer from uncontrolled diffusion of corrosive bromine particularly at high temperatures. That is because the interaction between polybromide anions and the commonly used complexing agent (N–methyl–N–ethyl–pyrrolidinium bromide [MEP]) decreases with increasing temperatures, which causes serious self-discharge and capacity fade. Herein, a novel bromine complexing agent, 1–ethyl–2–methyl–pyridinium bromide (BCA), is introduced in Br-FBs to solve the above problems. It is proven that BCA can combine with polybromide anions very well even at a high temperature of 60 °C. Moreover, the BCA contributes to decreasing the electrochemical polarization of Br⁻/Br₂ couple, which in turn improves their power density. As a result, a zinc–bromine flow battery with BCA as the complexing agent can achieve a high energy efficiency of 84% at 40 mA cm⁻², even at high temperature of 60 °C and it can stably run for more than 400 cycles without obvious performance decay. This paper provides an effective complexing agent to enable a wide temperature range Br-FB.     

Chemistry enhanced shear thickening polishing of Ti–6Al–4V

To obtain the great surface quality of Ti–6Al–4V and achieve high efficiency in the polishing process, the chemistry enhanced shear thickening polishing (C-STP) was proposed, and the polishing performance of different pH slurry was studied. The results show that the material removal rate gradually increases as the pH value decreases from 10 to 1, and the best surface quality is obtained at pH 2. The corrosion current density and potential were measured by potentiodynamic polarization under three typical pH values. It is confirmed that the most massive corrosion rate presents at pH 2, and the passive film is most susceptible to be produced at pH 10. The reaction resistance was measured by electrochemical impedance spectroscopy to clarify the polishing mechanism. Under acidic conditions, the chemical reaction product on the surface can be quickly removed by mechanical action of the abrasive. On the contrary, the passive film formed on the surface under the alkaline condition is difficult to be removed. The corrosion reaction products were determined by X-ray photoelectron, and the chemical reaction under acid-base environment was derived. MRR reached 107.3 nm/min under the selected process parameters, and the surface roughness (S_a) is reduced from 124 nm to 8.6 nm within 15 min.     

Smart-microstructures of composites for electrical contacts with frameless packing of Cr and W in copper

W₄₅Cu₅₅, Cr₆₅Cu₃₅, and Cr₃₂W₁₄Cu₅₄ alloys were obtained in order to study the mechanism of “smart response” of the structure of these alloys when using them as arc-resistant circuit-breakers. These alloys differ from industrial ones with frameless packing of Cr and W phases in the copper matrix. The alloy production method is based on the infiltration of copper melt into a mixture of non-compacted Cr and W powders under vibration exposure (80 Hz). The research results show an increase in the arc resistance of contacts when changing from “frame” packing of W to “frameless,” as well as the decisive role of Cr in the processes of self-dispersion of arc-resistant phases and passivation of W and Cu. Based on the obtained results, conclusions are drawn about the advantage of frameless packing of arc-resistant phases in copper and the reasons for the “smart behavior” of the structure of Cr-containing contacts in response to functional loads in the presence of oxygen and an inert atmosphere.     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.     

Surface generation mechanism of ceramic matrix composite in ultrasonic assisted wire sawing

Ceramic matrix composites (CMC) are highly required in many fields of science and engineering. However, the CMC parts always have poor surface finish. This study attempts to improve cutting performance of CMC material by combing the advantages of ultrasonic assisted cutting and diamond wire sawing. Cutting force, surface roughness, machined edge and tool wear are analyzed based on experimental results. It shows that the oscillatory movement of tool edges provides positive effect on particle ejection and residual material reduction. Ductile chip formation can be achieved due to the small tip radius of grits. Obvious decrease in cutting force, surface roughness and tool wear are obtained. Moreover, burrs, fuzzing and fracture are reduced. Meanwhile, both the surface characteristics and shape accuracy are significantly improved. These results provide a valuable basis for application of ultrasonic assisted wire sawing and understanding of CMC cutting mechanisms.